MicroDAQ toolbox

• Introduction — Introduction to MicroDAQ toolbox.
• Toolbox start guide — Explains how to setup and build first model for MicroDAQ using MicroDAQ toolbox for Scilab
• Blocks
  • MicroDAQ blocks HOWTO — Explains usage of MicroDAQ blocks for code generation ans host simulation mode
  • mdaq_adc — Reads MicroDAQ analog inputs (AI)
  • mdaq_dac — Writes MicroDAQ analog outputs (AO)
  • mdaq_dio_config — Configures MicroDAQ DIO functions and direction
  • mdaq_dio_get — Reads MicroDAQ DIO state
  • mdaq_dio_set — Sets MicroDAQ DIO state
  • mdaq_encoder — Reads MicroDAQ quadrature encoder
  • mdaq_func_key — Reads MicroDAQ function key state
  • mdaq_led — Sets MicroDAQ LED state
  • mdaq_mem_read — Reads MicroDAQ memory
  • mdaq_mem_write — Writes data to MicroDAQ memory
  • mdaq_param — Sets data to MicroDAQ DSP application
  • mdaq_pwm — Sets PWM outputs
  • mdaq_setup — Configures Xcos model for MicroDAQ
  • mdaq_signal — Reads signal data from MicroDAQ DSP application
  • mdaq_stop — Ends model execution
  • mdaq_tcp_recv — Receive data over TCP/IP from specified remote machine
  • mdaq_tcp_send — Sends data to remote TCP host
  • mdaq_time — Returns current time
  • mdaq_to_file — Saves data to file
  • mdaq_udp_recv — Receives data from UDP host
  • mdaq_udp_send — Sends data to remote UDP host
• C/C++ code integration
  • Introduction — C/C++ code integration tools introduction
  • Custom 'My step' Xcos block for MicroDAQ — This guide shows how to build custom Xcos block which can be used for code generation and host simulation mode
  • mdaqBlock — Initializes MicroDAQ block structure with default values
  • mdaqBlockAdd — Generates MicroDAQ block from provided block structure
  • mdaqBlockBuild — Build/Rebuild MicroDAQ custom block C/C++ source code
  • mdaqBlockDelete — Deletes MicroDAQ user block
• DSP managment
  • mdaqDSPBuild — Build model for MicroDAQ DSP
  • mdaqDSPSignal — Register SIGNAL block
  • mdaqDSPSignalRead — Read SIGNAL block data
  • mdaqDSPStart — Starts DSP application on MicroDAQ
  • mdaqDSPStop — Stop currently running DSP application
  • mdaqDSPTerminate — Force to terminate currently running DSP application
• Examples
  • Custom UART Xcos block — This guide shows how to build custom UART communication block using MicroDAQ API.
• Data acquisition
  • mdaqAIRead — Reads analog inputs
  • mdaqAIScan — Starts scanning operation and reads acquired data
  • mdaqAIScanInit — Initiates analog input scanning session
  • mdaqAIScanStop — Stops analog input acquisition
  • mdaqAOScan — Starts analog output scanning
  • mdaqAOScanData — Queues data to be output
  • mdaqAOScanInit — Initiates analog outputs scanning session
  • mdaqAOScanStop — Stops analog output scanning
  • mdaqAOWrite — Writes analog outputs
  • mdaqDIORead — Reads DIO channel
  • mdaqDIOFunc — Controls alternative DIO function
  • mdaqDIOWrite — Writes DIO channel output
  • mdaqEncoderInit — Initializes quadrature encoder module
  • mdaqEncoderRead — Reads quadrature encoder
  • mdaqKeyRead — Reads MicroDAQ function key state
  • mdaqLEDWrite — Sets MicroDAQ LED state
  • mdaqMemRead — Reads MEM Write block data
  • mdaqMemWrite — Writes MicroDAQ memory
  • mdaqPWMInit — Initializes PWM module
  • mdaqPWMWrite — Writes PWM duty
• Utility functions
  • mdaqClose — Close connection with MicroDAQ
  • mdaqFileData — Reads data from MicroDAQ user disk
  • mdaqHWInfo — Checks MicroDAQ hardware configuration
  • mdaqLog — Prints or saves MicroDAQ system logs.
  • mdaqOpen — Creates connection with MicroDAQ
  • mdaqPing — Checks connection with MicroDAQ
  • mdaqSetIP — Sets IP address
  • mdaqToolboxPath — Returns MicroDAQ toolbox install path